μεταχειρισμένα Akai AA1030 Amp - Radio FM Reciever

Πληρως λειτουργικος Δεκτης / Ενιστυτης / PreAmp.
Δεν αναβει το λαμπακι του καντραν...θελει αντικατασταση. (Τελευταια Φωτο).

Πολυ καλη επιλογη για ακροαση μεσω PicUp, CD Player, Radio Stations κλπ.
Ta Ηχεια σας 8Ω, οδηγουνται εξαιρετικα καλα (Almost any Vatage)

Akai AA-1030 receiver 
The Akai model AA-1030 , is another machine that's packed with power.
Minimum 30 watts per channel RMS at 8 Ω  from 20 to 20,000 Hz with no more than 0,3% T.H.D. And frankly we're probably being over modest. It's certainly worth emphasising here that the power rating is a minimum. Typical samples, when measured with both channels driven at 1 kHz into 8 Ω , should demonstrate quite clearly the importance of comparing specification in power output.
There's a delicately balanced flywheel for picking your spot on the waveband. And with AFC (Automatic Frequency Control) you get perfect FM centre tuning with completely drift-free reception. A low noise FET and 3-gang frequency rectilinear variable capacitor in the front end eliminate intermodualtion distortion for clear broadcast reception. Ceramic filters in the FM IF section give better reception of weak signals. IHF sensitivity is 2,0 µV. The Phase-Lock-Loop circuit produces complete stability with separation better than 40 dB
As with the AA-1020, the AA-1030 also has variable FM muting to let you select not only the strongest stations and the weakest stations the tuner can pick up, but any point in between as well. There's also a level adjuster to allow you to cut out local atation interference. There are separate bass and treble tone controls; loudness switch; high and low filters; the same comprehensive tape dubbing facilities as the AA-1020 (you can connect two tape decks for simultaneous recording from a single source and Tape monitor 1 has parallel DIN and phone connections), two sets of phono jacks; aux jacks; connections for two speaker systems; FM and AM antenna terminals and a distance/local switch.

Specifications
Amplifier Section
Continuous Power Output: 
30 watts per channel , min. RMS, at 8 ohms from 20 Hz to 20 kHz, with no more than 0,3% T.H.D.
2 x 40 watts into 8 Ω  at 1 kHz, with no more than 0,3% T.H.D. both channel driven
2 x 50 watts  into 4 Ω  at 1 kHz, with no more than 0,3% T.H.D. both channel driven
Power Bandwidth (IHF) :  10 Hz to 60,000 Hz / 8 Ω  (Distortion within 0,3%)
Input Sensitivity/Impedance
Phono 1, 2 :  3 mV/50 k Ω
Tape 1, 2 :  150 mV/80 k Ω
Aux :  150 mV/80 k Ω
Signal-to-Noise Ratio (IHF)
Phono :  better than 80 dB
Aux :  better than 90 dB
Channel Separation (IHF):
Phono :  better than 55 dB (at 1 kHz)
Equalizer Phono :  RIAA ±1 dB
Tone Controls
Bass :  ±10 dB at 100 Hz
Trebble :  ±10 dB at 10 kHz
Loudness Contour: +10 dB at 100 Hz; +6 dB at 10 kHz (Volume control set at -30 dB position)
Filter:
High :  -8 dB at 10 kHz
Low :  -8 dB at 50 Hz
FM Tuner Section
Frequency Range:  88 MHz - 108 MHz
Sensitivity (IHF):  1,9 µV
Capture Ratio (IHF):  1,5 dB
Selectivity (IHF):  better than 70 dB at 98 MHz
Signal-to-Noise Ratio :  better than 70 dB
Image Rejection:  better than 65 dB at 98 MHz
IF Rejection:  better than 90 dB at 98 MHz
Spurious Rejection:  better than 70 dB at 98 MHz
Harmonic Distortion
Mono :  less than 0,2%
Stereo :  less than 0,4%
FM Stereo Separation:  better than 40 dB ( at 1 kHz)
FM Muting:  Variable (2 µV to 100 µV) On-Off
Antenna Input:  300 Ω  (balanced), 75 Ω  (unbalanced)
AM Tuner Section
Frequency Range:  535 kHz to 1605 kHz
Sensitivity (IHF):  200 µV/m (Bar antenna); 5 µV (ext. Antenna)
Image Rejection:  better than 55 dB at 1 kHz
IF Rejection:  better than 45 dB at 1 kHz
Selectivity (IHF):  better than 30 dB at 1 kHz
AM Distortion:  less than 0,6%
Signal-to-Noise Ratio:  better than 50 dB
General Section
Semiconductors:  1 FET, 33 Transitors; 15 Diodes; 3 ICs
Power Requirements:  120 V, 220 V, 240 V 50/60 Hz
Dimensions (W x H x D):  440 x 140 x 350 mm (17,3" x 5,5" x 13,8")
Weight:  13 kg (28,6 lbs)